LG LSW350B Bedienungsanleitung PDF herunterladen (Seite 5)

ENGLISH

How to install the wall mount

Wall mount

screw

→ If the screw cannot be assembled in the

designated location inevitably, it can be

assembled by rearranging to the closest

location. But, do not change 2 or more locations

from the designated spot.

→ Assemble the wall mount screw on 2 left and 2

right location on the top part and 1 left and 1

right location on the bottom part.

→ At this time, use a + driver (manual or motorized)

or 8 mm wrench to tighten the screw so that the

wall, wall bracket and screw are completely

pressed against one another.

How to assemble the wall mount support and display

- Always install the display with 2 or more people.

* Assembling the wall mounting bracket, product

and safety clip.

* Caution - Prevent the power cord from being

pinched between the wall mounting

bracket and the set during

installation.

(A pinched power cord may cause

damage to the product.)

Safety clip

1. Set the display with the guide spacer assembled on the wall mount bracket on the wall in arrow direction. At this time,

align the bottom assembly part and lift the set up lightly to align the top part.

2. When adjusting the location, assemble the provide safety clip as shown in the picture to prevent the product from

moving. Tighten the safety clip screw completely. If the safety clip is not tightened as shown in the picture, the

product can fall off.

→ Pull on the bottom of the set to make sure the display is secure.

→ When fixing the product with the speaker to the wall, hold and lift up the product, not the speaker.

→ When installing a display rotated, only rotate the display 90 degrees (portrait mode). (VESA 300X300)

→ Make sure to keep a certain level of distance from the wall so that excessive force is not applied on the cable or

accessory.

→ When you push the product with excessive force, the product can be damaged.

INSTALLATION

- The picture may differ from the actual product.

How to Attach the Brackets for the Product to the TV

- If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and refer to the

technical service manual.

Guide Spacer

Guide spacer

screw

- Work procedure

1. Check to see if the display has screws

installed into the mounting holes. If so, remove

those.

2. Assemble the guide spacer and the guide

spacer screw in order as shown in the picture.

- Place the TV on a table with the screen

facing down. Make sure that you place it on

a flat surface covered with a soft cloth or

cushion to protect it from scratches.

- Secure the guide spacers to the TV with the

screws.Assemble the guide spacer to the

set by tightening the screw.Tighten the

screw until the set, guide spacer and the

screw are fully pressing against one

another.

- Use the + driver (manual or motorized)

when tightening the screw.

How to attach to masonry walls

Please follow the below direction.

- Check the material of the wall and the thickness of the finishing.

- Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and

hallow block that do not crack.

- Do not mount the device on the walls made from plasterboard or medium density fiberboard (MDF). In this case, the anchor

and screws must be inserted into the concrete behind the finish surface. If there is no concrete on the other side, then you must

first install a separate hanger to securely install the anchors and screws.

- When installing the product on wall material not designated, install the product so that each location can withstand the pull

out load of 70 kgf (686 N) and shear load of 100 kgf (980 N) or above.

d e

Wall mount screw

Anchor

- Use the Ø 8 mm drill bit for concrete and hammer (Impact) drill.

a. Use a drill bit Ø 8 mm to drill a hole for the anchor location within a depth of 80 mm - 100 mm.

b. Clean the drilled hole.

c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)

d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward.

e. Align the wall mount bolt to the hole and tighten it. Then, fasten the bolts at torque of 45 kgf/cm - 60 kgf/cm.

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

LG LSW350B Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein LG LSW350B