LG F1403FD5 Bedienungsanleitung PDF herunterladen

1 2

3 4

Schraubenschlüssel

• Water supply is not adequate in

area

• Water supply taps are not

completely open.

• Water inlet hose(s) are kinked.

• The filter of the inlet hose(s) are

clogged.

• Drain hose is kinked or clogged.

• The drain filter is clogged.

• Load is too small.

• Load is out of balance.

• The appliance has an unbalance detection

and correction system. If individual heavy

articles are loaded (ex. bath mat, both robe,

etc.), this system may stop spinning or even

interrupt the spin cycle altogether.

• If the laundry is still too wet at the end of the

cycle, add smaller articles of laundry to

balance the load and repeat the spin cycle.

• Is the door opened or not

completely closed?

• Water overfills due to the faulty water

valve.

• Water level sensor has malfunctioned.

• Over load in motor.

• The washer experienced a power failure.

Check another tap in the house.

Fully open tap.

Straighten hose(s).

Check the filter of the inlet hose(s).

Clean and straighten the drain hose.

Clean the drain filter.

For more detailed information,

please refer to “Cleaning the drain pump filter”

Add 1 or 2 similar items to help

balance the load.

Rearrange load to allow proper

spinning

Close the door completely.

If “ ”is not released, call for service.

Unplug the power plug and call for service.

Close the water tap.

Unplug the power plug.

Call for service.

Restart the cycle.

CAUTION

The appliance is not intended for use by young children or inﬁ rm persons without supervision.

Young Children should be supervised to ensure that they do not play with appliance.

60 - 100 cm

■

Installation of drain hose

Adjustable feet

• Proper level-adjustment of the washing machine

prevents excessive noise and vibration. Install

the appliance on a solid and level ﬂ oor surface,

preferably in a corner of the room.

• If the ﬂ oor is uneven, adjust feet as required.

(Do not insert pieces of wood etc. under the

feet). Make sure that all four feet are stable and

resting on the ﬂ oor. Then check that the appli-

ance is perfectly level. (Use a spirit level).

■

Level adjustment

■ Wooden ﬂ oors (Suspended ﬂ oors)

• Wooden ﬂ oors are particularly susceptible to vibration.

• To prevent vibration we recommend you place rubber cups under each foot, at

least 15mm thick under the washer, secured to at least 2 ﬂ oor beams with screws.

• If possible install the washer in one of the corners of the room, where the ﬂ oor is

more stable.

※

Insert the rubber cups to reduce vibration.

※

You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept.

Rubber Cup

Owner‘s Manual

Safety instructions for use

Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating

instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives

these operating instructions. The following warnings must be strictly observed for safety reasons. They must be read

before installing the appliance and putting it into operation.

• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance

only with cold drinking water and only for washing textiles with washing detergents designed for washing machines.

Every other use is improper and may lead to injuries, whereby the liability of the manufacturer will cease.

• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.

• Never modify the appliance on your own, as this is dangerous.

• This appliance is heavy. Transporting with care.

• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.

• All installation work must be carried out by a qualiﬁ ed ﬁ tter or technician.

• Have electrical connections done by a qualiﬁ ed electrician.

• Never place the appliance on the power cord.

• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.

• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug

- never disconnect by pulling the power cord. Never touch the plug with wet ﬁ ngers or hands.

• Do not overload the appliance.

• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.

• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite

or parts to warp.

• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and ﬁ re.

• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.

• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.

Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized

customer service.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explo-

sive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result

in ﬁ re or explosion.

• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain

remover has been used then make sure that the solvent has been carefully washed out before inserting the clothes

into the appliance. Oil may remain in the tub after a whole cycle resulting in ﬁ re during drying. So, do not load oily

clothes.

• Do not operate the appliance at locations where ﬂ ammable substances are present such as oil, benzene or highly

inﬂ ammable gas. Such materials may cause ﬁ re or explosion. Never use combustible detergents.

• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.

• After washing, keep the drum door open to protect the door seal.

• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of

scalding.

• Animals and children may get into the washing machine. So always check the appliance before using it.

• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.

• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machi-

ne.

• The product should be serviced and repaired only by the authorised customer service using original replacement

parts.

• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in

order to protect children.

• When placing on a carpeted ﬂ oor, make sure that the opening in the socket is not blocked.

• If the appliance has been under water then contact the customer service. There is danger of electric shock and ﬁ re.

• The cover cup of the ﬁ lter as well as the dispenser drawer may not be opened during the operation.

• Keep all washing powder and detergents away from children. Danger of poisoning.

Before use please read carefully the safety instructions!

Thank you for buying an LG fully automatic washing machine.

Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.

Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your

washing machine.

Remove Packaging

Requirements for installation site

Transit bolts

Electrical connection

Connecting water supply hose

• The appliance is ﬁ tted with transit bolts to prevent internal

damage during transport. Be careful, heavy load!

• Packing and all transit bolts must be removed before using

the washing machine.

• When unpacking the base, be sure to remove the additional

packing support in the middle of the base packing.

Store original packing for future move.

Dispose of packing material according to local regulations.

Unscrew the 4 bolts

using the spanner

supplied.

Keep the 4 bolts and the spanner for the future use. Reﬁ t transit bolts before transporting the appliance.

Level ﬂ oor: Permissible ﬂ oor gradient under entire washing machine

is 1˚ .

Power socket: Must be within 100 cm of either side of location of

washing machine. Do not overload the socket with more than one

appliance.

Additional Clearance: For wall, ﬂ oor and door space is needed.

(10cm: rear / 2cm:right & left side). Do not place or store laundry pro-

ducts on top of the washing machine at any times. They can damage

the ﬁ nish or controls of the machine.

1. Do not use an extension cord or double adapter.

2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualiﬁ ed person

to prevent danger.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out by qualiﬁ ed personnel. Repairs carried out by inexpe-

rienced persons may cause injury or serious malfunctioning. Contact your local service centre.

• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst

under pressure. The electronic control unit may become unreliable at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine

standing at room temperature for a few hours before putting it into operation.

• Two rubber seals are supplied with the water inlet

hoses. They are used for preventing water leaks.

• Make sure the connection to taps is tight enough.

• Periodically check the condition of the hose and

replace the hose if necessary.

• Make sure that there is no kink on the hose and

that it is not crushed.

Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)

Don’t strip or crossthread when connecting inlet hose to the valve.

If the water supply pressure is more than 1000kPa, a decompression

device should be installed.

Safety instuctions for the installation

Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the

washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from

obstruction by carpeting if the washing machine is installed on a carpeted ﬂ oor. In countries where there is a risk of cockroach

infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.

Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.

CAUTION about positioning the appliance

Install the washing machine on a ﬂ at hard ﬂ oor. Make sure that air circulation around the washing machine is

not impeded by carpets, rug etc.

•

Never try to correct any unevenness in the ﬂ oor using pieces of wood, cardboard or similar materials under the washing machine.

•

If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel

(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.

•

The washing machine must not be installed in rooms where the temperature may drop below 0°C.

•

Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.

•

Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between

the top of the washing machine and underside of the worktop.

CAUTION about the power cord

We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance

concerned, without any additional outlets or branch circuits. Check the speciﬁ cations of this owner‘s manual. Do not overload

wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or

cracked wire insulation are dangerous. Any of these conditions could result in electric shock or ﬁ re. Periodically examine the cord

of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have

the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical

abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular attention to plugs,

wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated

device in the mains supply.

CAUTION about location and moving

This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stop-

cock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no ﬂ oor drain (gully)

in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young

children becoming trapped inside. Packaging material (e.g. plastic ﬁ lm, Styrofoam) can be dangerous for children. There is a risk

of suffocation! Keep all packaging well away from children.

CAUTION about the ﬂ oor surface

• The installation surface must be clean, dry and level.

• Install washing machine on a ﬂ at hard ﬂ oor.

• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.

• The washing machine must be perfectly level and ﬁ rmly in position.

• It must not “see-saw” across corners under load.

• The installation surface must be clean, free from ﬂ oor wax and other lubricant coatings.

• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.

Name of product Front loading washing machine

Power supply 220-240 V~, 50 Hz

Size WxDxH mm: 600 x 640 x 850

Weight 68 kg

Max. Watt

2100 W

Wash capacity Refer to the Rating Label

Water consumption 63 ℓ

Permissible water pressure 1.0-10 bar (100-1000kPa)

Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in drum or pump.

Thumping sound Heavy wash loads may produce a thumping sound. This is usually normal.

Vibrating noise Have all transit bolts and packing been removed?

Water leaks. Check and tighten hose connections. Unclog drain pipe.

Contact plumber if necessary.

Excessive suds Too much detergent or unsuitable detergent.

Washing machine does not start Power cord may not be plugged in or connection may be loose.

Washing machine won’t spin Check that the door is ﬁ rmly shut.

Door does not open Once started, the door can not be opened for safety reasons.

Wait one or two minutes before opening the door to allow the electric

locking mechanism time to release.

Troubleshooting

To prevent internal dama-

ge during transport, the

special 4 bolts are locked.

If they are not removed, it

may cause heavy vibrati-

on, noise and machine to

malfunction.

Installation

Technical Speciﬁ cation

If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional

type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting

the tap into the adaptor.

The hose supplied with the machine must be used. Old hoses may not be reused

Close the holes with

the caps supplied.

Remove the 4 bolts

along with the rubber

bungs by slightly twis-

ting the bung.

P/No. :MFL62883845

F1403FD(1~9)

• The drain hose should not be placed higher than 100 cm above the ﬂ oor.

• Proper securing of the drain hose will protect the ﬂ oor from damage due to any water leakage.

• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.

1 2

Owner‘s Manual 1
F1403FD(1~9) 1

Inhaltsverzeichnis

Seite 1 - F1403FD(1~9)

412351 23 4Schraubenschlüssel6@• Water supply is not adequate inarea• Water supply taps are notcompletely open.• Water inlet hose(s) are kinked.• The

Seite 2

123AC B1 2 3 4 51 3ProgramFabric TypeWater Temp.(Option)CottonLightly soiled clothing and small loadsCottonQuickSyntheticBaby CareDelicateQuick 30Duve

Kommentare zu diesen Handbüchern

Keine Kommentare

LG F1403FD5 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Waschmaschinen LG F1403FD5 herunter. LG F1403FD5 Owner's manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Waschmaschinen LG F1403FD5