LG ARNU07GQAA4.ENWBLEU Bedienungsanleitung

www.lg.comPlease read this installation manual completely before installing the product.Installation work must be performed in accordance with the nat

1. The Outer diameter of Drain Hose(which is supplied with indoor unit) is17mm at connecting end, 600mmlong.2. Use commercial rigid PVC pipe forextens

Installation Manual 116. Installing Indoor unit6-1 Installation on the Floor.1. Fix up using 6 screws for floor installation.6-2 Installation on the

6-3 Half concealed installation.1. Make a wall hole of the size shown Fig-1.2. Installation of supplemental plate for attaching main unit• The rear of

Installation Manual 133.Piping Hole4. Remove the Deco Covers and Fixing IndoorUnit1) Remove the Deco Covers.2) Insert the Indoor Unit to the Wall hol

Flaring WorkMain cause for gas leakage is due to defect of flaring work. Carry out correct flaring work in the following proce-dure.Cut the pipes and

Installation Manual 15When you connect the refrigerant pipe, it is easier that you connect the gas pipe first.1. Hold up the Sensor Link.2. Separate

Connecting the installation pipe anddrain hose to the indoor unit.1. Align the center of the pipes and sufficientlytighten the flare nut by hand.2. Ti

Installation Manual 17Terminal block of indoor unitTerminal block of outdoor unit1(L) 2(N) 3(A) 4(B)Indoor power inputIDU IDUOutdoor unitIndoor unitC

Dip Switch SettingFor Multi V Models, Dip switch 1, 2, 6, 8 must be set OFF.That dip switch is used for other models.CAUTION18 Indoor UnitInstallation

Installation Manual 19InstallationENGLISH2. Outdoor UnitIn case that the products meet specific conditions, “Auto addressing” function can start auto

Console Type Indoor Unit Installation ManualTABLE OF CONTENTSo Installation guide mapo Connecting cableo Pipes: Gas sideLiquid sideo Insulation materi

20 Indoor UnitInstallationGroup Control SettingGNDSignal12 VMaster Slave Slave SlaveDisplay Error MessageOnly connect serial signal andGND lines betwe

Installation Manual 21InstallationENGLISHGNDSignal12 VSlaveSlaveMasterorDonʼt connect serial 12V lineLGAP Network SystemMasterMasterMasterDisplay Err

22 Indoor UnitInstallationGNDSignal12 VLGAP Network SystemFAUMasterFAUorSlaveMasterSlaveMasterMasterDisplay Error MessageDisplay Error MessageNM(3 s)(

Installation Manual 23ENGLISHInstallationLGAP Network SystemMasterMasterSlaveGNDSignal12 VSlaveSlaveSlaveorDisplay Error Message(3 s)(5 s)4. 2 Remote

24 Indoor UnitInstallationIndoor unit 2 EA +Wired remote controllerIndoor unit 1 EA +Wired remote controller 2 EAhPZCWRCG3 cable used for connectionhP

Installation Manual 25InstallationENGLISHThe A-weighted sound pressure emitted by this product is below 70 dB.** The noise level can vary depending o

26 Indoor Unit(1)MFL67798128() 17. 6. 30. 1:56 Page 26

(1)MFL67798128() 17. 6. 30. 1:55 Page 100

Installation Manual 3Signal receiverON/OFF button Operation lampAir purifier lampSignal receiverAir filterAllergy filterAir outletAir inletInstallati

Safety PrecautionsTo prevent injury to the user or other people and property damage, the following instructions must be followed.n Be sure to read bef

Installation Manual 5n OperationENGLISHSafety PrecautionsDo not modify orextend the powercable.• There is risk of fire orelectric shock.Do not let th

6 Indoor UnitSafety PrecautionsCAUTIONn InstallationAlways check for gas(refrigerant) leakageafter installation orrepair of product.• Low refrigerant

Installation Manual 7Installation• There should not be any heat source or steam near the unit. • There should not be any obstacles to the air circula

Indoor unit installation1. Preparation / Removing front panel1. Open the front grille by pulling forward2. Then pull out the link of grille from groov

Installation Manual 91. The location of hole is different depending on which side of the pipe is taken out.2. Drill a hole(Ø70mm) in the point indica