P/NO : MFL69485407INSTALLATION MANUALAIRCONDITIONERwww.lg.comPlease read this installation manual completely before installing the product.Installatio
10INSTALLATIONENGLISHDrill a Hole in the Wall- Drill the piping hole with a ø65 mm hole coredrill. Drill the piping hole at either the right orthe lef
INSTALLATION11ENGLISH1 Compare the flared work with the figureby.2 If a flared section is defective, cut it offand do flaring work again.Connecting th
12INSTALLATIONENGLISH- Press on the tubing cover and unfold thetubing to downward slowly. And then bendto the left side slowly.* The feature can be c
INSTALLATION13ENGLISHInstallation of Indoor Unit1 Hook the indoor unit onto the upper por-tion of the installation plate.( engage thethree hooks at th
14INSTALLATIONENGLISH1 Align the center of the pipes and suffi-ciently tighten the flare nut by hand2 Tighten the flare nut with a wrench3 When needed
INSTALLATION15ENGLISHType 'C' screwFinishing the indoor unit installation1 Mount the tubing holder in the originalposition.2 Ensure that the
16INSTALLATIONENGLISH2 Do not make drain piping like the follow-ing.* The feature can be changed according totype of model.Do not raiseWaterleakageAcc
INSTALLATION17ENGLISHManual the decor, air filter Assembly & Disassembly1,MFL69485407,영영 2017. 6. 25. 영영 3:20 Page 17
18INSTALLATIONENGLISHWiring Connection- Connect the wires to the terminals on the control board individually according to the outdoorunit connection.-
INSTALLATION19ENGLISHCAUTIONAfter the confirmation of the above conditions, prepare the wiring as follows:1) Never fail to have separate power special
2TIPS FOR SAVING ENERGYENGLISH• Do not cool excessively indoors. This may be harmful for your health and may consume moreelectricity.• Block sunligh
DIP Switch SettingIndoor UnitOutdoor UnitIn case that the products meet specific conditions, “Auto addressing” function can start automat-ically with
21ENGLISHINSTALLATIONGroup Control SettingGroup Control 1n Wired remote controller 1 + Standard Indoor UnitsSome products have no DIP switch on PCB. I
22ENGLISHINSTALLATIONGNDSignal12 VSlaveSlaveMasterorDonʼt connect serial 12V lineLGAP Network SystemMasterSlaveMasterDisplay Error MessageGroup Contro
23ENGLISHINSTALLATIONGNDSignal12 VLGAP Network SystemFAUMasterFAUorSlaveMasterSlaveMasterMasterDisplay Error MessageDisplay Error MessageNMGroup Contr
24ENGLISH2 Remote Controln Wired remote controller 2 + Indoor unit 1INSTALLATIONLGAP Network SystemMasterMasterSlaveGNDSignal12 VSlaveSlaveSlaveorDisp
25ENGLISHINSTALLATIONAccessories for group control settingIt is possible to set group control by using below accessories.Indoor unit 2 EA +Wired remot
The A-weighted sound pressure emitted by this product is below 70 dB.** The noise level can vary depending on the site.The figures quoted are emission
1,MFL69485407,영영 2017. 6. 25. 영영 3:20 Page 200
IMPORTANT SAFETY INSTRUCTIONS3ENGLISHIMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.Always comply with the following pr
4IMPORTANT SAFETY INSTRUCTIONSENGLISH- There is risk of fire or electric shock.• Install the panel and the cover of control box securely.- There is ri
IMPORTANT SAFETY INSTRUCTIONS5ENGLISHpanel, cabinet, top cover, control box cover are removed oropened.- Otherwise, it may cause fire, electric shock,
6TABLE OF CONTENTSENGLISH2 TIPS FOR SAVING EN-ERGY3 IMPORTANT SAFETY IN-STRUCTIONS7 INSTALLATION PARTS7 INSTALLATION TOOLS8 INSTALLATION MAP9 INSTALLA
INSTALLATION PARTS7ENGLISHINSTALLATION TOOLSNameQuantity ShapeInstallation plate1 EA1 EAType "A" screw5 EAType "C" screw2 EACloth
8INSTALLATION PARTSENGLISHINSTALLATION MAPVinyl tape (Wide)• Apply after carrying out a drainage test.• To carry out the drainage test, remove the
INSTALLATION9ENGLISHSelect the best Location - There should not be any heat or steam nearthe unit.- Select a place where there are no obstaclesaround
Kommentare zu diesen Handbüchern