LG LPT-EP551PS Bedienungsanleitung

Dome CameraOwner’s ManualMODEL: LPT-EP551PS / LPT-EP553PSLPT-EI551PS / LPT-EI553PSBefore installing and using the camera, please read this owner'

10Setting the SwitchThe DIP switch of the camera is one 8-bit switchesand employs RS-485 communication mode as basicuse. Switch settings are read into

11Alarm Output Mode SettingYou can set the Alarm Output to the normal open ornormal close mode.Camera ID SettingThis camera has the camera ID set to “

12ID SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW853 ON OFF ON OFF ON ON OFF OFF54 OFF ON ON OFF ON ON OFF OFF55 ON ON ON OFF ON ON OFF OFF56 OFF OFF OFF ON ON ON O

13ID SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8159 ON ON ON ON ON OFF OFF ON160 OFF OFF OFF OFF OFF ON OFF ON161 ON OFF OFF OFF OFF ON OFF ON162 OFF ON OFF OFF O

14Precautions• The connections should be made by qualifiedservice personnel or system installers in accor-dance with all local codes.• AC 24V can be u

15ALARM IN ConnectionsAn 8-pin harness are supplied with the camera asstandard accessories. Connect external sensors tothis connector. Input specifica

16Alarm Input functionListed below are the camera actions of alarm input function by different function status in each mode ALARM OUT ConnectionsConne

17To Alarm indicator 4To Alarm indicator 3To Alarm indicator 2To Alarm indicator 1To Alarm sensors8WhiteBlueGreenYellowOrangeRedBrownBlack7654321RS-48

18System ConnectionNote: When any peripheral is turned off and turned on again, the camera is also turned off and turned back on.Caution: Connect the

19BrownBlueYellowGreenRedBlackOrangeWhiteTo Alarm indicator 11 ALARM OUT 12 COM 13 ALARM OUT 24 COM 25 ALARM OUT 36 COM 37 ALARM OUT 48 COM 4To Alarm

2This lightning flash with arrowhead symbolwithin an equilateral triangle is intended toalert the user to the presence of uninsulat-ed dangerous volta

20Setup Menu OverviewSetup menus are shown in the table below. You can adapt the camera to your requirements by setting up therespective items in thes

21Setting Camera MenuThe buttons on the connected controller are used forsetup.Open Menu Display1. Select the number of the camera you want to setup a

22Camera Identification SettingOnly displays the camera’s ID. Use the internal 8 bit-DIP switch if you want to set ID.• Camera ID 0 can control all of

23Zoom Start settingSelects a zoom start position.Select [ZOOM START] option on the [FOCUS] menu,then select a zoom’s start position. (x1 - x26)Zoom E

24White Balance Control SettingsYou can set the white balance options using the[AWB] menu.General Operation1. Move the cursor to [AWB SET] on the [MEN

25Exposure SettingsYou can set the exposure options using the [AE]menu.General Operation1. Move the cursor to [AE] on the [MENU] screen 2. Press the r

26Automatic Gain Control (AGC) settingIf the images are too dark, change the maximum[AGC] value to make the images lighter. This optionis available on

27Electronic Sensitive settingThe electronic sensitivity enhancement functionvaries the shutter speed to increase the sensitivity inlow light conditio

28Auto Exposure Level SettingsYou can set the auto exposure options using the [AE LEVEL] menu.General Operation1. Move the cursor to [AE LEVEL] on the

29Special SettingsYou can set the special options using the [SPECIAL]menu.General Operation1. Move the cursor to [SPECIAL SET] on the[MENU] screen 2.

31. Read these instructions. - All these safety and operatinginstructions should be read before the product is operat-ed.2. Keep these instructions. -

30Color Setting You can switch the displayed picture to grayscale orcolor.Select [COLOR] option on the [SPECIAL] menu, thenselect an option (ON or OFF

31Motion Detection SettingThe motion detection detects the moving objects inthe scene by monitoring changes in brightness level.You can select the lev

32Privacy Masking SettingsUsing the LCC-K1000 or controller with Multix protocol for Privacy Zone Setting.This function is aiming at the protection of

33SpecificationsSignal System NTSC (High Resolution) PAL (High Resolution)Pick-Up Device 1/4” EX-view CCDTotal Pixels No. 410K 470KS/N Ratio More Than

4ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7IMPORTANT SAFETY INSTRUCTIONS . . . . . . . .3Contents . . . . . .

5xxPattern FunctionA routine of manual operations can be stored for 8minutes at the maximum and reproduced repeti-tively. The Panning, Tilting and Zoo

6Safety PrecautionsxxDo not attempt to disassemble the cameraTo prevent electric shock,do not remove screws orcovers. There are no user serviceable pa

7a Camera mounting bracketThe bracket is optional for surface installation.b Fall Prevention WireBe sure to hook the fall prevention wire into an brac

8Precautions• The following steps of installation and connectionwork should be done by qualified service person-nel or system installers and should co

9Pendant mount (LPT-EP551PS / LPT-EP553PS) Wall mount (LPT-EP551PS / LPT-EP553PS) How to install“A” Pipe threads should be clean andrust free. Use a