LG GT46SGP Bedienungsanleitung PDF herunterladen

SAFETY MESSAGES

INSTALLATION

THIS MANUAL CONTAINS SEVERAL IMPORTANT SAFETY NOTICES. ALWAYS READ AND OBEY ALL OF THE FOLLOWING

SAFETY MESSAGES.

DANGER

If you fail to follow these instructions you will be killed or seriously injured.

WARNING Misuses of the product will cause you physical damage or personal wounds.

CAUTION Inadequate use and installation will cause damage to your property.

All safety labels will inform you of potential danger, ways to reduce chance of injury and what can happen if instructions are not followed.

WARNINGS AND IMPORTANT SAFETY MEASURES

Read all instructions before use your product.

WARNING. This appliance contains a small amount of isobutane refrigerant (R600a), natural gas with high environmental compatibility, but it is

also combustible. When transporting and installing the appliance, care should be taken to ensure that any part of the refrigerating circuit is damaged.

Refrigerant squirting out of the pipes could ignite or cause an eye injury. If a leak is detected, avoid any naked ﬂames or potential sources of ignition and

air the room in which the appliance is placed for several minutes.

In order to avoid the creation of a ﬂammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may

be placed depends on the amount of refrigerant used. The room must be 1m

in size for every 8 grams of R600a refrigerant inside the appliance.

The amount of refrigerant in your particular appliance is shown on the identiﬁcation plate inside the appliance. Never start up an appliance showing any

signs of damage. If in doubt, consult your service center.

CAUTION. Risk of Fire, keep in mind next caution points when you move or install your refrigerator, gas used in your appliance is inﬂammable:

ţ Avoid use any ﬂame or heat sources to access to sealing system when the appliance is being fulled with refrigerant.

ţ In case of refrigerant leak the area must be completely ventilated before start working.

ţ Be careful, DO NOT damage refrigeration circuit.

CAUTION. Risk of Fire or Explosion (Inﬂammable Refrigerant), the refrigerator only must be repaired by qualiﬁed personal. Do not drill refrigeration

circuit. Read instructions in your Owner’s Manual before use this product, all safety messages must be followed.

CAUTION. This appliance is not intended for being used by children, persons with physical or mental disabilities, persons with reduced sensory or

mental capacity, or persons with lack of experience or know-how, unless they have supervision or instruction in relation to the use of the appliance by the

person responsible for their safety. Children should be supervised to assure that they do not play with the appliance.

NEVER USE EXTENSION CORDS. Never connect multiple machines in the same socket, this can cause wiring to overcharge,

warming, voltage vibrations and bad functioning.

ELECTRICAL CORD REPLACEMENT. If electrical cord gets damaged it must be replaced by the manufacturer, our service center

or qualiﬁed LG Electronics personnel to minimize risks.

GROUND CONNECTION. In case of electrical surge, connection to ground will reduce risks of electric shock hazard. This

unit must be grounded. Consult a qualiﬁed electrician. When moving your refrigerator, be careful not to step on the electrical

cord with the machine’s rollers.

¡¡¡NEVER KEEP EXPLOSIVES INSIDE!!!. Never store explosive substances or chemicals in your refrigerator such as benzene, alcohol,

etc. It is DANGEROUS!!

DANGEROUS FUN. An empty refrigerator can be very dangerous for children. Remove doors or magnetic packaging when not be in use

or secure it in a way to make it impossible to open and allow a child to go in as this can lead to suffocation. Never allow a child to climb, hang

or play with the refrigerator compartments. They can get hurt themselves and damage the refrigerator.

PLUG ACCESS. The refrigerator-freezer must be placed in a way that the electrical cord can be pulled easily in case of emergency.

WHAT TO DO WITH YOUR OLD REFRIGERATOR. Your refrigerator contains liquids (refrigerant, lubricant) made of recyclable materials.

All these materials must be sent to a recycling waste disposal site as they can be reused after a speciﬁc recycling process. Contact local

authorities.

WHEN CLOSING REFRIGERATOR DOOR. Never place your thumb or ﬁngers on the superior part of the handle, as it can be

pressed against the lower part of the freezer handle. Keep away all ﬁngers from injury areas such as where doors close cabinets and hinges,

etc. Be careful when closing doors if children are nearby.

NEVER USE MECHANICAL DEVICES. Never use mechanical devices or any other means to accelerate the thawing process,

use only those which are approved by the manufacturer.

DO NOT STORE ANIMALS. Do not store any living animal in your refrigerator.

NEVER STORE ELECTRONIC DEVICES. Never use electronic equipment to store food unless they are speciﬁc models

approved by the manufacturer.

WARNING. The maintenance of the lowest area from the refrigerator’s back side (see image) only must be done by qualiﬁed

personal, do it by non qualiﬁed technician can produce risk of electric shock.

CAUTION. This appliance is intended to be used in household and similar applications such as: staff kitchen areas in shops,

ofﬁces and other working environments; farm houses and by clients in hotels, motels and other residential type environments; bed

and breakfast type environments; catering and similar non-retail applications.

WARNING. Keep free from any obstruction the air vents around the appliance and assembly structure.

WARNING. Do not damage the refrigerant circuit.

1. UNPACKING

Before installing your refrigerator, remove any tape or temporary stickers. Do not remove any stickers that feature warnings, the model serial number or the

technical label of the product located on the back of the refrigerator. To remove adhesive tape residue, rub it well with your ﬁngers and a little liquid detergent.

Clean with warm water and let dry.

Do not use sharp instruments, rubbing alcohol, ﬂammable liquids or abrasive cleaning products to remove the adhesive tape or glue. These products can

damage the surface of your refrigerator. The shelves come already installed in their factory position. Remove the shelves and replace them according to

your spacing needs.

2. INSTALL IT AWAY FROM HEAT SOURCES AND HUMID AREAS

In places with high temperatures, freezing capacity can be affected and cause high consumption of electrical energy. Never install in

places with high humidity as this can cause oxidation and electric shock hazard.

3. THOUGH AND EVEN FLOOR

Your refrigerator must be leveled and placed on a strong ﬂoor. An unstable installation can produce noise and vibrations.

If the ﬂoor is uneven, level the unit by twisting the height adjusting screw, this will eliminate unwanted sounds and

vibrations.

NOTE: For adjusting leveling screws lift the front of the refrigerator and insert a screwdriver in the holes located in the

leveling screws, then turn them clockwise ( ) to raise your refrigerator and counter-clockwise ( ) to lower it.

4. AMBIENT TEMPERATURE

The refrigerator will work efﬁciently if room temperature is between 10 °C and 43 °C (50 °F and 109,4 °F).

5. A PROPER DISTANCE FROM ADJACENT ITEMS

Adequate air ﬂow is needed for an efﬁcient operation. Keep your refrigerator at a relative distance from other objects.

Reduced distances between the unit and other nearby objects can diminish freezing capacity and rise consumption of

electrical energy. NOTE: Be careful when you open the doors, one of them can be open more than the other one. Avoid

hit the doors with items around the refrigerator area.

The room must be 1m

in size for every 8 grams of R600a refrigerant inside the appliance. The amount of refrigerant

in your particular appliance is shown on the identiﬁcation label inside the appliance.

WARNING. EXCESSIVE WEIGHT HAZARD. Use the assistance of two or more persons to move or install the

refrigerator. Not following these instructions may cause injury to the back and other parts of the body.

6. WAITING PERIOD

Wait at least one hour before connecting, after installation was completed.

7. CONNECTION

DANGER.

FOR YOUR PERSONAL SAFETY, this device must be properly grounded. Connect to a single undamaged

socket. Not having proper installation will require you to call qualiﬁed personnel to achieve it.

Do not, under any circumstance, cut or extract the third prong from the plug. It is your responsibility and obligation to replace

two-prong outlets with that of an adequately grounded three-prong outlet.

WARNING. REPLACING ELECTRICAL CORD, if the electrical cord is damaged, it must be replaced by our service

center or qualiﬁed LG technician to avoid any risk. NEVER disconnect the refrigerator by pulling the electrical cord, always

grip the plug ﬁrmly and disconnect it directly from the outlet.

8. BEFORE STORING FOOD

Leave your refrigerator working from 2 h to 3 h before storing food. If operation is interrupted wait 5 min before trying again.

9. IN CASE OF UNINSTALLING

If you wish to dispose of your refrigerator, keep in mind the following WARNING.

WARNING. If the use of this unit is no longer needed, please contact local authorities to dispose of this product in a safe way due contains Pentane-

cycle or pentane as gas for insulation and R600a as refrigerant. Insulation gases and refrigerant require a special elimination process. This product

contains ﬂammable insulation and refrigerant.

NOTE: This guide covers different models. Your refrigerator could have some or all of the features and parts listed below. The location of some of the parts

may not correspond with your model.

Freezer Shelf (Glass)

Temperature Control (Freezer)

External Temperature Control (Refrigerator) *

Internal Temperature Control (Refrigerator) *

Refrigerator Lamp (LED)

Refrigerator Shelf (Glass)

Hygiene Fresh Filter *

Cover for Vegetable Drawer *

Vegetables & Fruits Compartment (“2 in 1 Box” or “1 Box”) *

Magic Crisper, cover for vegetable drawer, it controls humidity

Vegetable Drawer, keeps fruits and vegetables fresh

Leveling Screws

Freezer Big Basket

Easy Ice Maker

Home Bar (Ice Container)

Freezer Small Basket

Water Tank *

Refrigerator Big Basket

Multi Flow Air Duct, distributes air to all refrigerator compartments

Egg Tray

Water Dispenser *

* In some models

Freezer Shelf (Glass)

Moving Twist’n Serve (Ice Maker)

Internal Temperature Control (Refrigerator)

Refrigerator Lamp (LED)

Refrigerator Shelf (Glass)

Magic Crisper, cover for vegetable drawer, it controls humidity

Vegetable Drawer, keeps fruits and vegetables fresh

Leveling Screws

Freezer Big Basket

Temperature Control (Freezer)

Water Tank *

Refrigerator Big Basket

Multi Flow Air Duct, distributes air to all refrigerator compartments

Egg Tray

Water Dispenser *

* In some models

Back

lower

area

10 cm.

3 cm.

IDENTIFICATION OF PARTS

1. CONNECTION

Remember that your refrigerator must be grounded.

CAUTION. If operation is interrupted, wait 5

minutes before restarting it.

2. ICE MAKER OPERATION

Type 1, “Moving Twist’n Serve”

ţ For ﬁlling your ice maker, ice container must be

removed (Figure 1), after that you can pull the ice

shelves out (Figure 2) and ﬁnally ﬁll them until the

indicated level (Figure 3).

WARNING. Fill only with potable water.

ţ Place the ice shelves in their original position. For removing ice cubes

twist the knob clockwise, the ice cubes will fall into the ice container

(Figure 4).

ţ"DDPSEJOHUPZPVSTQBDFOFFETZPVSJDFNBLFSDBOCFNPWFEGSPNPOF

side to another, you just have to move in the direction wanted (Figure 5).

Type 2, “Easy Ice Maker”

ţ To make ice cubes, pull out the ice shelves and pour water on the shelves (Figure 6). Then place in their original position until you hear a “click” sound.

WARNING. Fill only with potable water.

WARNING. Make sure the level of water in the shelf is even on the entire surface, guiding yourself with pointing arrows (Figure 7). Water must not

surpass this level as it can get spilled when opening or closing door.

ţ The ice maker takes around 4 hours to produce ice cubes. Check

the ice status through the transparent panel. To remove ice

cubes, carefully pull the drawer lever (Figure 8). The ice cubes will

fall into the ice container (Figure 9).

WARNING. Refrain from pulling the lever before ice cubes

have been completely made, as this can cause water to spill,

freeze, and cause the container to stick to the Ice maker (Figure

10). If water spills, immediately wipe it off with a cloth. Avoid

heavy ice accumulation in the container as this can cause

problems to move the lever and/or container.

3. THAWING

Thawing occurs automatically, you do not need to worry about this.

Thawed water will ﬂow into the evaporation shelf at the back of the refrigerator.

4. AUTO CHECK

Your refrigerator has the capacity of auto checking. If any failure comes to happen a code will be displayed to help

the technician for its repairing. While this code is on display, the rest of the functions of control a visualizing will not

be functioning.

NOTE: In the temperature controls, the code is represented with a no consecutive blinking of the LED (left to

right/down to up) as would be in the normal mode (Figure 11).

5. TEMPERATURE CONTROL SETTINGS

ţ Refrigerator temperature will always be the same, despite ambient temperature changes. We recommend not to

change the temperature adjustments after they have been set unless it is necessary. This refrigerator contains a

button which controls the refrigerator’s temperature and a knob to control the freezer’s temperature.

ţ The correct temperature conﬁguration for the refrigerator compartment should be 37,4 °F (3 °C).

ţ The correct temperature conﬁguration for the freezer compartment should be -2,2 °F (-19 °C).

ţ The refrigerator compartment contains a temperature sensor which will automatically start and stop the compressor functions as needed.

5.1 External Temperature Control (in some models)

ţRefrigerator: Monitors the refrigerator temperature. External temperature control in certain models, it may vary according to product speciﬁcation (Figure 12

&13).

Door Alarm:

You will hear an alarm when the refrigerator or freezer door stays open for over a minute. NOTE: Freezer alarm is only available for 16 cubic

feet capacity models. The alarm will continue with this sound every 30 seconds, it will stop once both doors have been closed. By pressing the button,

you can activate or deactivated this function.

Express Freeze: Once this button is pressed, the refrigerator will begin to cool at full power to a maximum of two 2 hours. Pressing the button a second

time will deactivate the mechanism. This feature will not be available if “Vacation (Eco Friendly)” is on.

Hygiene Fresh:

This function will keep clean your refrigerator for a longer period of time, this ﬁlter eliminates bacteria and bad odors inside your

refrigerator. For its activation press the button and the icon will be illuminated also the ﬁlter light will be on (this feature is only available on some models,

it may vary according to the model).

Fridge: This feature allows you to adjust the refrigerator temperature. The number appearing on the screen will match the degrees of the inside of the

refrigerator. You can choose from 7 different settings, from 0 °C to 6 °C (32 °F to 42,8 °F).

Vacation (Eco Friendly):

This feature helps you to save energy during vacation periods or when the refrigerator is not used for periods longer than 2 days.

It can be turn on by pressing the button “Vacation (Eco Friendly)”, the LED indicator lights up when it is activated. For turning off you must press button

“Vacation (Eco Friendly)” once more. This function will be automatically deactivated when refrigerator compartment door is open or button “Fridge” is

pressed. NOTE: This mode can not be activated when function “Express Freeze” is being used.

Temperature Conﬁguration

HOW TO ADJUST

COLDER RECOMMENDED COLD

Press the “Fridge” button until the desired

temperature be reached, at this point the

indicator reads 0 °C (32 °F).

Press the “Fridge” button until the indicator reads

3 °C (37,4 °F). This is the desired temperature for

best performance of this unit.

Press the “Fridge” button the temperature 6 °C

(42,8 °F) appears on the screen.

NOTE: To check functions of the freezer temperature control, please look for Internal Temperature Control Function.

5.2 Internal Temperature Control

ţ Freezer: Controls the air ﬂow from the freezer to the refrigerator (Figure 14).

HOW TO ADJUST COLDER RECOMMENDED COLD

To adjust the position knob turn

to either side to make it turn. The

arrow will set the temperature in

your freezer.

Adjust the control in position

number 5.

Adjust the control in position

number 3.

Adjust the control in position

number 1.

ţ Refrigerator

: Controls the temperature of the refrigerator. Internal Temperature Control it may vary according to every model (Figure 15).

HOW TO ADJUST

COLDER RECOMMENDED COLD

Press the button until the last LED is turn on. Press the button until the third light is on. This

temperature is the recommended one for the

optimum refrigerator performance.

Press the button until the ﬁrst light is on. The

temperature is the minimum.

1. SHELVES

The shelves of your refrigerator can be adjusted to comply with your storage necessities; depending on the model you have it can include glass shelves or

plastic shelves. Storing your foods together and adjusting the shelves to different heights will help you to locate what you need in an easier way. This also

helps your refrigerator to stay shut longer which will save you energy. IMPORTANT: While your refrigerator glass shelves are cold do not clean with hot or

warm water. The glass shelves may break if they’re exposed to rapid temperature changes or hard impacts. For your safety the glass shelves are made out of

tempered glass so when at breaking they will fracture into tiny fragments. NOTE: Be careful while moving or relocating the shelves, they are heavy. If moving

the shelves is required keep in mind to locate them in a safe environment to prevent them from breaking.

OPERATIONS AND FUNCTIONS

Model with:

ţ External Temperature Control (Refrigerator)

ţ Home Bar

ţ Water Dispenser

Model with:

ţ External Temperature Control (Refrigerator)

ţ Water Dispenser

Model with:

ţ Internal Temperature Control (Refrigerator)

ţ Water Dispenser

Model with:

ţ Internal Temperature Control (Refrigerator)

Ice Container

Figure 5

Figure 1

Figure 3

Figure 2

Ice Shelves

Ice Container

Ice Shelves

Water Level

indicators

Water level

must be even

Figure 7Figure 6

The ﬁrst LED is off

Figure 12. External Temperature Control (in some models)

Shelf Refrigerator

In order to remove the refrigerator shelves follow the next

instructions:

1. Take the shelf from the back.

2. Lift it from the bottom by using the necessary strength

(Figure 16).

3. Release the holders (Figure 17).

4. Slide it towards outside (Figure 18).

NOTE: Be careful when you remove the shelves from the

refrigerator, because they are secured to the refrigerator walls.

Shelf Freezer (Identify your type)

Type 1 (Normal Shelf)

If you need to remove the shelf of the freezer, follow the instructions for not damaging it:

NOTE: Be careful when you remove the shelves from the refrigerator, because they are

secured to the refrigerator walls.

1. Hold the shelf by the front part (Figure 19).

2. Pull the shelf outwards lifting it slightly until it leaves the holder from the bracket

(Figure 20).

Type 2 (Shelf with Moving Twist’n

Serve Ice Maker)

1. If you have Twist’n Serve Ice

Maker, place it in the middle of

the shelf, then take the shelf

from the back side and lift it up

applying the necessary force

(Figure 21).

2. Release the holders (Figure 22)

and pull it out (Figure 23).

2. COMPARTMENTS

ţ Door Baskets

Door baskets can be taken off in order to clean them better.

1. To remove the basket, raise it and pull it out.

2. To replace the basket again slide it on the desirable guide and push it down until it is tighten (You will listen a “tick”).

WARNING. Someone could get hurt if the baskets are not well assembled. DO NOT allow children play with baskets. Sharp

corners on basket could cause injury.

NOTE: Empty the food charge before you move the door basket.

ţ Compartment “2 in 1 box” / Vegetables and Fruits Compartment (in some models)

Even with the door open, warm air can not affect the freshness zone, so you can keep it stored fresher.

The compartment should be correctly closed, because having the door open could affect the

refrigerator’s performance. The compartment can be opened by pulling the tray.

NOTE: Check the position before storing the food because it can clog if it is not closed properly.

ţ Vegetable Drawer (Magic Crisper)

The magic crisper allows a better preserva-

tion of your fruits and vegetables allowing to

easily control the level if humidity inside. It

has a vent located in the inner wall of the lid

to let humidity in or out.

To remove the vegetable drawer, follow the next instructions:

1. With both hands take the cover, tilt it up and pull it out towards the outside until it stops. Slightly lift the front part and

pull the rest, in order to completely remove the drawer (See ﬁgure 24).

2. To relocate the drawer slip out towards the front until it stops.

ţ Compartment “Ice Home Bar” (certain models)

In order to obtain the ice without opening

the door, open the ‘Home Bar’ door only by

pressing the “PUSH” button (located at the

door of the “Home Bar”).

3. WATER CONTAINER (some models)

Your refrigerator has a system that allows you having cold water without opening refrigerator door. For dispensing water, push backward the

dispenser lever with a glass until the water ﬂows.

NOTE: After using your dispenser, it is normal if some drops fall, you can reduce this by removing slowly the glass from the lever.

3.1 Water Tank Cleaning

For cleaning the water tank of your dispenser, follow the next steps:

ţ Take the water tank with both hands and pull it out to you, this will remove it from refrigerator (Figure 25).

ţ Once the tank is uninstalled from the door, lift up the holders of the lid and take it out (Figure 26).

ţ Wash the tank with water and do not use detergents or cleaners with odor, after this, dry with a piece of cloth (see Figure 27).

ţ Finally, align the lid with the water tank (see ﬁgure 28), then close the holders (see Figure 29), you must listen a “click”, this means that the lid has been

correctly assembled.

3.2 How install the Water Tank

For installing the tank in its original position (in refrigerator’s door), follow the next

instructions:

ţ Take the water tank and insert the valve in the hole of the refrigerator (Figure 30).

ţ Put the tank over the guides and push it down (Figure 31).

NOTE: If the water container is not well placed, water could spill or drain and no water will

come out from the dispenser in the door.

3.3 Filling Water Tank

For supply the tank with water, follow the instructions below:

ţ With the tank already assembled in the refrigerator, lift the tank’s lid and use a glass or jar

for ﬁll up the tank (see Figure 32).

ţ Close the lid by pushing and release until you hear a “click”, this means that the lid was

correctly closed (Figure 33).

ţ Dispense 2 or 3 times to purge the system.

NOTE: Do not ﬁll the tank completely in order to avoid water spills, the maximum capacity it

is indicated in your water tank.

WARNING. Fill only with potable water. Using other beverages (as beer, soda or liquids with

sugar) may damage the dispensing system.

If you need to empty the water tank, follow the next steps:

ţ Remove the water tank and its lid, see section “3.1 Water Tank Cleaning”.

ţ Dispose the leftover water.

ţ Assemble the lid and put the tank in the refrigerator (See section “3.2 How Install the Water Tank”).

4. HYGIENE FRESH FILTER (in some models)

CAUTION. Before installing or using the product make sure to read the Owner’s Manual carefully to use the product accurately as intended. This

Hygiene Fresh ﬁlter has the antibacterial function of removing the virus or bacteria inside the refrigerator and the deodorizer function to remove the scent.

Your Hygiene Fresh system has three different operation modes:

Off Mode Auto Mode Power Mode

In this mode the ﬁlter is not

operating, the icon will be turned

off.

This mode is activated when

you press the button of this

function (only the central part

is illuminated), in this feature

the ﬁlter works for periods of 10

minutes and stops for one hour,

this performance continues

repeatedly.

To activate this feature is

necessary press twice the button

(central part and word “POWER”

will be illuminated when this

function is selected), in this mode

the ﬁlter works for 10 minutes and

stops for 5 minutes, this function

continues for the ﬁrst 4 hours.

5. SMART DIAGNOSIS

(in some models)

Use the function to contact the service center and receive precise diagnosis when the refrigerator malfunctions or fails. Use it only to connect to the

consultant and do not use it in normal times.

5.1 How to use this function

If you want to activate this feature please identify your refrigerator type.

Type 1 (Models with Internal Temperature Control)

ţ Open both doors (freezer and refrigerator) and identify the switch

type of your appliance, it may vary between button type (Figure 34)

and magnetic type (Figure 35). The button type switch can be 1

or 2 switches, this may vary according to your model speciﬁcation.

ţ For button switch:

1. Press the switch 5 times for a period of 8 seconds (Figure 36) and

immediately place the telephone near to the speaker placed in the

top right (Figure 37), conﬁrm that the microphone is towards to the

speaker (Figure 37), then 4 short tones will be heard and the speaker

will emit a sound no longer that 8 seconds.

2. Keep the phone in place until the tone transmission has ﬁnished.

Once the data transmission is completed and the tones have

stopped, resume your conversation with the specialist, who will

then be able to assist you in using the information transmitted for

analysis.

ţ For magnetic switch:

1. Open refrigerator door and close it once, then open it 5 times for a

period of 8 seconds, now the SMART DIANOSISI

feature is active.

2. Immediately place the telephone near to the speaker placed in the

top right (Figure 37), conﬁrm that the microphone is towards to the

speaker (Figure 37), then 4 short tones will be heard and the speaker

will emit a sound no longer that 8 seconds.

3. Keep the phone in place until the tone transmission has ﬁnished.

Once the data transmission is completed and the tones have stopped, resume your conversation with the specialist, who will then be able to assist you in

using the information transmitted for analysis.

Type 2 (Models with External Temperature Control)

1. During three seconds press the button “Fridge” located in your Temperature

Control (Figure 38), after this all the icons will be turned off during 2

seconds (Figure 39) and “Fridge” option will show a number 3 on the screen

(Figure 40).

2. Now you must open both doors and 5 seconds later the SMART

DIAGNOSIS

will be activated.

3. Place the phone near the speaker hole at the top right (Figure 37). Check if

the speaking side (microphone) of the telephone is toward the speaker hole.

4. Do not take away the telephone while data is being transmitted. During the

data transmission for smart diagnosis, wait with the telephone placed near

to the speaker hole at the top right side. The diagnosis will end when on

the screen appears a letter “E” blinking three times (Figure 38), ﬁnally the

refrigerator returns to the values set before diagnosis.

CAUTION. The transmission sound may be irritating. Do not take away the

telephone until the sound stops for good diagnosis.

After the completion of the data transmission, listen to the explanation of the consultant about the result of the SMART DIAGNOSIS

. When the data

transmission is completed, along with the display of the data transmission completion, the refrigerator will be automatically turned off and on a few seconds

later. Listen to the explanation of the consultant about the result of the analyzed diagnosis and follow the instructions.

Please consider next points when you are using SMART DIAGNOSIS

ţ Difference of the regional call qualities may have inﬂuence on the function.

ţ If you use home phone, better communication performance will enable much better service.

ţ Smart diagnosis data transmission may not be ﬂuent due to call quality problem, and in such case, smart diagnosis service may be difﬁcult.

In order to avoid bad or unwanted odors, is important to keep the refrigerator clean. Any spilled food must be cleaned immediately; they can stain and/or

acidify the plastic parts of the refrigerator if they are let to get dry.

WARNING.

ţ Before installing, cleaning or change LED lamps you must disconnect refrigerator. When you have ﬁnished, connect the refrigerator and set the temperature

control (thermostat, refrigerator o freezer) to the desired position.

ţ Clean any humidity to avoid any liquid might get into any electrical part.

ţ Do not touch the frozen parts with wet objects, humid or wet hands, they can stick to frozen surfaces.

Exterior. Use a warm mixture of mild detergent or soap to clean the refrigerator’s surface. Clean with a damp cloth and dry immediately.

Interior. It is recommended to clean the interior often. Wash all the baskets and drawers with a mixture of bicarbonate or mild detergent with water. Clean

and dry. Using other kinds of products might damage your refrigerator.

After Cleaning. Check that the electrical cord is not damaged or overheated and it is properly plugged.

)

Figure 15. Refrigerator Internal Temperature Control (certain models).

Figure 14. Freezer Internal Temperature Control. Turning knob (all

models).

NOTE: Be careful of not blocking or moving with food packages

the temperature controls, you might change or not recognize the

temperature in which your refrigerator is set.

Figure 4

Ice Maker (Easy Ice Maker)

ţ Remove the ice shelf from the kit (Figure 42).

ţ Clean the inside and the outside of the ice shelf

with a mild soap, rinse with tap water (Figure 43).

ţ Use a damp piece of cloth and dry (Figure 44).

CAUTION. Do not immerse the ice shelves in

water. If you immerse them, you must dry them

completely.

Door lining and gaskets. For plastic parts do not use

cleaners, hard detergents, bleach or cleaners with

petroleum.

Plastic Parts. Do not use paper towels, abrasive cleaners or ﬂammable products, these could damage or scratch the product.

Back Cover. In order to get an efﬁcient performance of your refrigerator, clean its back cover at least twice a year. Verify that electrical cord is not damaged

and the plug is not overheated and it’s connected in outlet in a proper way.

Water Container

1. Remove the water container, it is no necessary to empty it before

remove (Figure 45).

2. Remove the container lid, opening the snaps and wash it with dish

washing detergent.

3. Rinse thoroughly under water (Figure 46).

4. Wipe it with a clean cloth (Figure 47).

ţ Keep fresh food in the refrigerator compartment.

ţ Freeze only small amounts of food.

ţ After you freeze some food, once you thaw it do not freeze it again, it looses its taste and nutritional value; after thawing it, you might

keep it in the refrigerator up to 48 hours.

ţ Do not store food that might get decomposed under low temperatures (ie. pineapple, bananas and cantaloupe).

ţ Do not store garlic in the refrigerator.

ţ When you store food in the refrigerator use closed containers in order to avoid odor mixing and loosing of humidity.

ţ Always clean the food before placing them in the refrigerator. Wash and dry the fruits and vegetables. Keep fresh food in the refrigerator.

ţ It is recommendable to store onion in plastic bags to avoid other food odor to get mixed with it odor.

ţ If you are going to store ice cream for a long period of time, place it on the freezer shelf and not on the freezer door.

ţ When storing eggs always place them in the highest shelf or in the ﬁrst basket in order to keep them fresh for a longer period of time.

ţ Throw away any food that is being decomposed; it may contaminate other foods.

ţ Store cold cuts, cheese and sausages in bags or plastic sealed containers.

ţ Do not store on freezer glass containers, they might break.

ţ Do not store hot food inside the refrigerator they might decrease the refrigerator’s efﬁciency.

ţ For models with water dispenser it is recommended change water in container at least once per week.

ţ Do not store any medicine in your refrigerator because they can be damaged or cause an unexpected reaction.

The next table explains to you the recommended temperature adjust in relation with food amount:

Food Amount Refrigerator Temperature * Freezer Temperature

When a large amount of food is stored

you need to adjust the controls in the

coldest temperature (for refrigerator)

and normal temperature for freezer

compartment.

Type 1)

For this control is necessary adjust in 0 °C (32 °F).

Type 2)

To reach a colder temperature verify that the last

LED is turned on.

Adjust the control in position number 3.

When you store a regular amount of food,

both controls must be adjusted in middle

position.

Type 1)

To reach a medium temperature adjust your

control in 3 °C (37,4 °F).

Type 2)

To adjust in a medium temperature you must verify

that third LED is on.

Adjust the control in position number 3.

For a refrigerator with a low amount of

food, it’s necessary adjust the controls in

the less cold positions.

Type 1)

Adjust in 6 °C (42,8 °F) for reach a less cold

temperature.

Type 2)

For a less cold temperature verify that only the ﬁrst

light is on.

Adjust the control in position number 1.

* Refrigerator control may vary according to your model speciﬁcation.

The refrigerator does not

work

ţ Check if any fuse is broken in the electric facility.

ţ Check if the power cord is correctly plugged.

ţ Check if the power outlet is not damaged.

ţ Identify if there are any high consume electrical appliances working at the same time, unplug the one that are not necessary.

There is a power interruption

In case of a black out, call your electric company and ask how long it will last.

ţ*ODBTFPGBIPVSPSMFTTCMBDLPVUEPOPUPQFOUIFSFGSJHFSBUPSUIJTXJMMLFFQUIFGPPEGSFTI

ţ*ODBTFPGBMPOHFSCMBDLPVUEPPOFPGUIFGPMMPXJOHPQUJPOT

1. Pull out all of the frozen food and keep them in an ice chest.

2. Put 2 lbs (0, 907 Kg) of frozen ice (make sure you use gloves) for each square foot (28 L) inside the freezer. This task will

preserve the food for 2 to 4 days. While handling dry ice (CO

), wear gloves to protect your hands from frostbite.

3. In case you do not possess neither ice chest or dry ice (CO

), consume your food as soon as possible.

The temperature of the

refrigerator or the freezer is

too warm or hot

ţ Check that the temperature control is in the right position.

ţ Place the refrigerator away from any heat sources or direct sunlight.

ţ Open the doors only when is necessary.

ţ There is too many food that blocks the air vents.

ţ Don’t let the doors open for a long period of time.

I can hear some weird or

abnormal sounds

ţ Check that the refrigerator is placed over an even leveled surface, if not, adjust the refrigerator using the leveling height

adjusting screws.

ţ Remove the unnecessary object from the back or top of the refrigerator.

ţ Check that the voltage is the correct one, if not call your electric company.

There are some odors in the

refrigerator

ţ Store all food in sealed containers.

ţ Frequently clean the refrigerator inside.

Some humidity is formed in

the cabinet’s surface

ţ When the weather is humid is normal.

ţ The door might be opened, check that is properly closed.

The front part of the

refrigerator is getting warm

ţ Do not worry, is part of the normal functioning of the refrigerator, and this happens in order to avoid condensation or “sweat”.

If this comes to happen, just clean with a dry piece of cloth.

The compressor works too

frequently and for extended

periods of time

ţ Check if the temperature controls are placed in the maximum, if so, placed them in the middle setting.

ţ Check that the doors are properly closed.

ţ Do not store over heated products.

ţ Do not let the doors open for a long period of time.

ţ Move away from any heat sources the refrigerator.

REMEMBER: In a power failure, a full freezer stays cold longer than a partially ﬁlled one. A freezer full of meat stays cold longer than a freezer full of baked

goods.

1. THE OVERALL PERFORMANCE OR EFFICIENCY OF YOUR REFRIGERATOR MAY BE AFFECTED IF:

ţ It is placed near a heat source or humid area.

ţ You open the door frequently.

ţ If you introduce water or any object in the cold air vents.

ţ You block the air vents with food.

ţ You store hot food.

2. DURING VACATIONS WE RECOMMEND YOU THE FOLLOWING:

ţ If the vacations are for a short period of time place the freezable food in the refrigerator.

ţ If you are going to be outside or away for a longer period of time, do the following:

1. Take out all food.

2. Unplug the electrical cord.

3. Leave the doors open to avoid bad odors.

4. Thoroughly clean the refrigerator.

5. Empty and clean the water bin not forgetting to purge the system (turning on the switch).

3. IF YOU ARE PLANNING TO MOVE OR TO CHANGE YOUR REFRIGERATOR FROM ITS CURRENT POSITION

ţ Remove and secure all attachments inside the refrigerator.

ţ To avoid any damage to the leveling height adjusting screws, turn them completely until the base.

ţ Place the electrical cord in the hook located in the upper left side.

ţ Clean and empty the water container and do not forget to purge the system (turning on the switch).

ţ After these procedures, you will be able to move your refrigerator.

ţ When you move your refrigerator, place a protection sheet, such as packing cartoon under the refrigerator to avoid ﬂoor damage. Always pull your

refrigerator straight out. Do not shift from side to side or “walk” the refrigerator when you are moving it.

ţ Use the assistance of two or more persons to move or install the refrigerator. Not following these instructions may cause injury to the back and other

parts of the body.

4. IN CASE OF REFRIGERANT LEAK

ţ Do not touch the refrigerator or the outlet and ventilate the room immediately.

ţ The explosion by spark may cause ﬁre or burn.

ţ Because this refrigerator uses natural gas (isobutene, R600a) as the environment-friendly refrigerant, even a small amount (80~90 g) is combustible.

ţ When the gas is leaked by the severe damage during delivering, installing or using the refrigerator, any spark may cause ﬁre or burn.

5. LAMP REPLACEMENT (LED)

Your refrigerator has a LED lamp for changing it you must call Service Center to perform the replacement

by qualiﬁed technician.

WARNING. In case of replacement, the new lamp must have the same speciﬁcation than the original

one.

6. THE FRONT AREA WARMS UP

The front wall of the cabinet of the refrigerator might warm up sometimes specially during installation.

DO NOT ALARM! It’s normal due to avoid humidity or “sweat”.

7. THE BACK AND LATERAL SIDE OF THE REFRIGERATOR WARM UP (some models)

¡DO NOT ALARM! The warming up is normal because in both sides the refrigeration pipes are located.

WARNING. In case of your refrigerator was damaged for some ﬂood, do not use it until qualiﬁed

technician conﬁrm its performance.

WARNING. When the door of the

“Home Bar” is open, children might

harm themselves when walking around;

to avoid any damage, avoid children to

play with or near the “Home Bar”.

“Home Bar”

Door

Ice Container

Push down

CLEANING

Figure 10

Lever

Ice

Maker

Figure 8

Ice

Container

Figure 9

Absorb

Moisture

Too much

Humidity

Release

Moisture

Low

Humidity

Ven t

PUSH

Figure 25 Figure 26 Figure 27 Figure 28 Figure 29

Lift up

Align the lid

with the tank

Press to close

Guide

Figure 31Figure 30

Figure 32 Figure 33

Lid

WHAT TO DO WHEN...

WHAT YOU NEED TO KNOW ABOUT YOUR REFRIGERATOR

Back

Side

Lateral

Side

Front

Side

Frontal View of your Refrigerator (it may vary according to the model purchased)

Figure 45 Figure 47

Water Tank

Lid

Figure 46

STORING FOOD SUGGESTIONS

Screwdriver

Leveling

Screw

Duplex Outlet

Make sure the

connection is

grounded

Three

terminal

plug

External Temperature

Control at Freezer Door

Home Bar (Ice Container)

in front of freezer door

Water Dispenser in front

of Refrigerator Door

Water Dispenser in front

of Refrigerator Door

Screwdriver

Leveling

Screw

www.lg.com

MFL40273819

MANUAL DE USUARIO

REFRIGERADOR CON

CONGELADOR SUPERIOR

Lea detenidamente este manual antes de empezar a utilizar el refrigerador

y guárdelo como referencia para el futuro.

Model Name / Nombre de Modelo:

GT40BGP, GT40BGW, GT40HGP, GT40SGP, GT40WGP, GT46BGP, GT46HGP, GT46SGP, GT46WGP,

GT46HGPP.

OWNER’S MANUAL

TOP MOUNT

REFRIGERATOR

Please read this manual carefully before operating your set and retain it for

future reference.

ENGLISH

ESPAÑOL

Compartment

“1 Box”

Compartment

“2 in Box”

Figure 40 Figure 41

Figure 38 Figure 39

FRONT

The error is represented with letters

REFRIGERATOR TEMPERATURE CONTROL

(CONTROL DE TEMPERATURA REFRIGERADOR)

COLD

(MENOS FRIO)

COLDER

(MAS FRIO)

Door

Alarm

Express

Freeze

Hygiene

Fresh

Reset 5sec.

Fridge

Vacation

(Eco Friendly)

Figure 11

Figure 12. External Temperature Control (in some models)

Figure 13. External Temperature Control (in some models)

Figure 18Figure 17Figure 16

Shelf

Holder

Shelf

Bracket

Holder

Figure 19 Figure 20

Holder

Shelf

Figure 22

Figure 21

Figure 23

Ice maker Shelf

Figure 24

Valve

Valve’s Hole

Figure 36

Figure 37

Figure 35

Figure 34

USING YOUR REFRIGERATOR

Figure 42

Figure 43

Figure 44

Ice

Maker

Ice

Shelves

)

ZZA!

ODA

SODA

Jug

Helado

Yogurth

Mantequilla

CARNE CONGELADA

PIZZ

Jug

Helado

Yogurth

Mantequilla

CARNE CONGELADA

Helado

Yogurth

Mantequilla

CARNE CONGELADA

1 2

Inhaltsverzeichnis

Seite 1 - REFRIGERATOR

SAFETY MESSAGES1INSTALLATIONTHIS MANUAL CONTAINS SEVERAL IMPORTANT SAFETY NOTICES. ALWAYS READ AND OBEY ALL OF THE FOLLOWING SAFETY MESSAGES.DANGER

Seite 2 - Oriﬁcio para

ESTA SIMBOLOGIA SERÁ UTILIZADA EN ESTE MANUAL PARA INDICAR ACCIONES QUE NO DEBEN REALIZARSEPELIGRO Si no sigue las instrucciones de inmediato p

Kommentare zu diesen Handbüchern

Keine Kommentare

LG GT46SGP Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Nein LG GT46SGP herunter. LG GT40BGW,GT46SGP,GT40BGP,GT40WGPP,GT46BGP,GT46HGP Owner’s Manual [el] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein LG GT46SGP